Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - abrogard

Pages: [1]
I have a clone that I lost the software for.  I didn't realise it was unique.  But apparently it was.

Because using the software I normally connect to my Foscams with I get no configuration option on screen. From this camera.  From all the others I do of course.  But not this one.

I can connect to it using push firefox mode and I can control the pan/tilt.  But I can't change its settings.

Can anyone suggest anything that might help?  Other software perhaps more 'powerful'?

Some cmd prompt method of sending it commands?

General Discussion / Better Software To Connect With Foscam Clone?
« on: November 19, 2017, 05:10:27 am »

 I have a couple of Foscam clones and they came from different vendors.

 One of them has no 'advanced' option or any other way of changing the configuration.

  So how did I get it set up in the first place?

  ah, good question.  Well I think it came with its own software for finding it and talking to it.

  I've lost that now.  Can't find it.

  Anyone got any idea of how I could perhaps get at this camera and reconfigure it for our new local network which uses the 10.x.x.x  series instead of the 198.x.x.x  ?

General Discussion / How To Log Contacam Into a Foscam Clone?
« on: November 19, 2017, 05:06:58 am »

 My Contacam won't log in to my foscam clone and I think it probably because of that second menu thing that it throws up - asking what mode you want, for IE or Firefox or Mobile.

 Is there any way to deal with this and use Contacam with a clone?

General Discussion / No Configuration Option On This Foscam Clone
« on: October 05, 2017, 05:10:43 pm »

I have a Foscam clone that I can access via ethernet cable but I find no configuration options on it when I get there.

Opening in Firefox.

I need to configure it because we have a new router so I have to change the wifi setup.

I assume it is some kind of software thing - like it needs something better than firefox - anyone know of anything that might do the trick?

General Discussion / CLONE OR CCTV?
« on: March 06, 2016, 09:16:36 pm »
My clones have been guarding the place well for years but we got thieved the other week, finally.

And caused a rethink.  My clones are, in fact, not monitored. So they are virtually sham.

Monitoring, when I've looked into it, seems to be a difficult and maybe expensive job.  I finished up hassling a lot with Ispy and couldn't get reliable performance out of it and had hassles getting a dedicated computer to handle the job with Ispy looking at four cameras.

That's the first issue: Monitoring.

The second issue is quality.  Even if my cameras were monitored the pictures are never going to show details of a face, especially night time when the thieves are about.

So I'm thinking I maybe need to go CCTV for better resolution.  For instance:

But there's 720 Clones now offered on eBay.  Would they do, I wonder?

We are watching a driveway, a backyard and the interior of a workshop shed. 

Over the years things change. I'm just wondering what things are like now.  What would you advise as the best way to go now?  Foscam clone ? or CCTV ? - wireless or cable? 

And what monitoring software?

And what computer platform.  I had an old computer I thought would be good for the job with Linux on it but it couldn't handle it.

Lastly the audio side. Any comments on the audio hardware and tactics to be used nowadays?  There seem to be lots of 8G cheap audio recorders they market as 'spy' recorders. I suppose they are voice activated and you leave them on site and check them each morning.

General Discussion / What Happens After Reset?
« on: May 28, 2015, 09:53:31 pm »
I have a couple of Foscam clones.  Lost the password for one of them.  Did a hard reset with a piece of wire and the thing rebooted, went into that seek patrolling sequence.

But now I can't connect with it at all.

What should happen after a reset?  Just resets the password or more than that?  Which is what it looks like.

Have to go back to hooking up with ethernet, finding it, configuring IP address and everything, is that right?

Pages: [1]