News:

Did you know - Google aren't very nice.  Apparently we're all evil pirates here on OpenIPCam, and they cancelled my adsense account due to that.  Sigh.

Recent Posts

Pages: [1] 2 3 ... 10
1
Firmware / Hi3516 Unknown command 'root' - try 'help'
« Last post by anil_argede on June 19, 2017, 06:41:23 am »
Hi everyone,
I tried access to Hi3516 in my camera module. I used from a link to do this.
Link: https://felipe.astroza.cl/hacking-hi3518-based-ip-camera/
I wanna access root but got an error.


System startup


U-Boot 2010.06 (Jun 28 2016 - 09:04:41)

Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:   
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  1 ... 0
hisilicon #
hisilicon # root
Unknown command 'root' - try 'help'
hisilicon #
hisilicon #


Any ideas to solve this error? I already apologize for my english.
2
Help / Any instant on cameras?
« Last post by SlowBro on June 13, 2017, 03:49:47 pm »
Are there any cameras that come on very quickly, or which can be put in deep sleep mode to wake quickly?

I'd like to create a wire-free battery-powered motion sensing setup. The motion could be detected via IR sensor and a microcontroller could start up a camera. Images would be transmitted over Wi-Fi or cellular.

If the Foscam-style cams offer sleep mode that could work.
3
General Discussion / Sannce I21AG Locking down
« Last post by widemouth on June 11, 2017, 08:40:20 am »
Thought I would post my experience with this camera.

On Bootup this camera attempt network connections to:

baidu.com
shifen.com
szxingweilai.cn
ec2-52-8-140-28.us-west-1.compute.amazonaws.com

And also directly attempts to connect to IP: 115.28.242.250

Horribly unsecure so it you have the ability to block these on your router then I suggest you do.

Other than that, it appears to be a good and cheap 720p camera.


4
Hacking & Modding / Re: H3518 / UART TxRx
« Last post by admin on May 31, 2017, 01:04:49 am »
HI3518

Look at the data sheet, and see what the RX / TX pins are, then follow those around the board to see if they end up anywhere accessible.

T19 / T18 according to the data sheet
http://www.datasheetspdf.com/PDF/Hi3518/853432/64

Also look at this -

https://felipe.astroza.cl/hacking-hi3518-based-ip-camera/
5
Hacking & Modding / H3518 / UART TxRx
« Last post by maxxxxpower on May 23, 2017, 10:34:59 am »
Have a FW issue with my camera. Need to get back in to it via serial to restore the FW. I don't seem to be able to find the UART TxRx on this board though. Can anyone help?

6
Similar Hardware / Please i need help with my FOSCAM 9821
« Last post by dumaster on May 15, 2017, 01:08:57 pm »
Please i need help with my FOSCAM 9821

My Foscam 9821 (plate FI9821A_MAIN_2V1 code) stopped working, as I am technician in electronics and have some maintenance equipment and decided to try to fix it, I made a serial connection to monitor the boot, to my surprise the initialization already hangs in the u- boot and does not enable or the option to enter the mode upload, I believe that the data in the flash memory SPI corrupted or it is damaged, I'm thinking of removing it from the board to make a re-programming and verification test, but it would need a complete DUMP ROM for this card model or similar, and that includes everything, kernel, root and also the u-boot, so I can use my programmer to reprogram the SPI memory and return life to my camera, please have someone to help me would be very grateful.

Eduardo Lopes  :)
7
Hacking & Modding / Please i need help with my FOSCAM 9821
« Last post by dumaster on May 15, 2017, 01:08:17 pm »
Please i need help with my FOSCAM 9821

My Foscam 9821 (plate FI9821A_MAIN_2V1 code) stopped working, as I am technician in electronics and have some maintenance equipment and decided to try to fix it, I made a serial connection to monitor the boot, to my surprise the initialization already hangs in the u- boot and does not enable or the option to enter the mode upload, I believe that the data in the flash memory SPI corrupted or it is damaged, I'm thinking of removing it from the board to make a re-programming and verification test, but it would need a complete DUMP ROM for this card model or similar, and that includes everything, kernel, root and also the u-boot, so I can use my programmer to reprogram the SPI memory and return life to my camera, please have someone to help me would be very grateful.

Eduardo Lopes  :)
8
Firmware / Re: ldr file research
« Last post by asf21 on May 12, 2017, 01:53:51 pm »
Nobody has this file please?  :'(
9
Help / BB-1000 IP Camera
« Last post by mrblack on May 10, 2017, 07:26:20 pm »
Hi everyone,

Looking for some help with a generic IP camera that was given to me.

I would like to get the RTSP stream of this camera rather than use the MIPC App to view the camera feed.

Any pointers on where to start?
10
Firmware / Re: ldr file research
« Last post by asf21 on May 02, 2017, 04:05:04 pm »
Pages: [1] 2 3 ... 10