News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Author Topic: I deleted Image: 0 name:BOOT INFO. Could anyone send it to me.  (Read 55299 times)

  • No avatar
  • *****
June 28, 2011, 08:12:19 pm
@Celem Well, you got him to follow simple instructions from the first page finally ::)

If you want to walk him through finding out what hardware he has, that will be fun.

@Casbeto.

Suggest try flash the kernel file from Kaicom firmware folder, and a romfs from one of the 2M filesystems

The newest camera's have Pixart PAP7501V sensors and RT3070 wifi.
If yours is an older model, then SunPix sensor and vt6656 wifi possibly, or rt73 wifi.

I guess I should roll out a linux + romfs that outputs some debugging info so that we can find that out.

June 28, 2011, 08:20:02 pm
this makes ipcam bought it about 3 months and has wifi.

  • *****
June 28, 2011, 09:21:36 pm
Ram & cpu good. Flash suspect

June 28, 2011, 09:47:47 pm
Thank you for everything!!

  • *****
June 28, 2011, 10:10:24 pm
Lawrence (admin) just proposed a good solution to possibly salvage your camera - namely using firmware intended for a 2MB flash. In this way, if the flash area is in higher memory, your camera would still work - if the sensor is compatible.

June 28, 2011, 10:13:35 pm
ok, just do not know even how. rs

  • *****
June 28, 2011, 10:21:00 pm
Lawrence, I enjoy solving crossword puzzles - do them every day. Maybe a connection?

  • *****
June 28, 2011, 10:24:00 pm
casbeto, Lawrence is suggesting to load the 2MB firmware at:
http://www.openipcam.com/files/Firmware/KaiCom%20IP1018%20Firmware/

The sensor is unlikely to be correct, but if it will load and run (at the console) it would prove that your flash's upper memory was bad.

June 28, 2011, 10:31:38 pm
ok, but I have to use what command?
 mx ou fx ?
« Last Edit: June 28, 2011, 10:37:16 pm by casbeto »

  • *****
June 28, 2011, 10:53:01 pm
Follow the notes at that link, but the sequence is probably:
Code: [Select]
fx 7 linux.zip 0x7F020000 0x8000 -acxz
fx 6 romfs.img 0x7F0E0000 0x7F0E0000 -a
fx 8 webui.bin 0x7f180000 0x7f180000 -a

Good luck

June 29, 2011, 02:35:02 am
ahhh....

set -ip0 10.0.3.200

Can we change the MAC Address with this or similar command or does it need reflash of Image 0. I have cameras which have all the same MAC.

EDIT:
ok, found it myself it is set -mac0 [addr]
« Last Edit: June 29, 2011, 02:39:33 am by Borsti92 »

June 29, 2011, 08:41:46 am
the set command is not accepted!

  • *****
June 29, 2011, 10:02:16 am
1. Your camera can correctly install and run a linux kernel and romfs directly to RAM.
2. All actions involving FLASH appear to fail.
3. The ls command shows "BOOT INFO" as mounted yet subsequent accesses indicate that it is corrupted.
4. Conclusion: your FLASH has a problem.

My final recommendation. If this fails, consider the camera a source of spare parts.

Using the bootinfo file previously posted:
http://goo.gl/7vQpV
enter the following commands:

DEL -all
DEL b1
fx 0 "BOOT INFO" 0x7F010000 0x7F010000 -f   (NOTE: on your PC xmodem send the bootinfo file referenced above)

  • No avatar
  • *****
June 29, 2011, 12:43:50 pm
maybe only the fx command is broken, it would be worth trying to flash via tftp

June 29, 2011, 12:57:13 pm
I will perform the tests, and the night stand for you to see!

 Thank you all!