News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kozmo2k

Pages: [1]
1
Hacking & Modding / Re: Reset jumper pins
« on: June 06, 2014, 01:11:40 pm »
After a long fight with this camera, I came across some software that enabled me to change the IP address and Port# for the camera. Now I can (happily) access the camera's web interface and video streams...
For anyone interested here is a ling to the (sorry, only for windooze) software:
https://dl.dropboxusercontent.com/u/18476770/IP.Cameras/Vanxse/MonitorClient.zip
No the most intuitive software to use, but it got me where I needed to be.
And the camera's firmware:
https://dl.dropboxusercontent.com/u/18476770/IP.Cameras/IPC.Upgrade%20Software.N18A_1_2_2_561120B14.version.7z
Best regards..
./b

2
Firmware / Unpack Firmware ROM file
« on: June 03, 2014, 03:46:44 pm »
I found a Firmware file for my generic (china/ Vanxse) IP Cam.
Want to have a look inside the ".rom" fil, but having hard time trying to unpack it.
Can anyone here point me in the right direction, i.e. what software to use?
Link to file:
https://dl.dropboxusercontent.com/u/18476770/IP.Cameras/IPC.Upgrade%20Software.N18A_1_2_2_561120B14.version.7z

Greatly appreciated

3
Hacking & Modding / Re: Telnet password and username for IPC
« on: May 13, 2014, 08:51:13 am »
That is all I was able to pull with FTP.

4
 @spooniester : would you care sharing how you were able connect to the IPCamera with Telnet?

5
Hacking & Modding / Re: Reset jumper pins
« on: May 11, 2014, 05:53:35 pm »
Yeah... no go on the Onvif Device Manager on resetting the camera. Onvif can't connect...
I can only see ports: 21 (FTP), 23 (telnet), 5050 (mmcc?) and 5051 (tcpwrapped) with nMap scan...

6
Hacking & Modding / Re: Telnet password and username for IPC
« on: May 11, 2014, 03:01:37 pm »
PM sent with links...

7
Hacking & Modding / Re: Reset jumper pins
« on: May 11, 2014, 02:48:47 pm »
I had no problem with the colour picture, for all of the 20 seconds I looked at it, before I tried to change the IP address and Port#. That's when I lost access to the camera web interface...
Where can i find the Onvif Software you mentioned, is the the one from Sourceforge?
However, I was able to find the camera's firmware, but it is out of my league to unpack it and investigate.
If someone wants to play with it, here it is:
https://dl.dropboxusercontent.com/u/18476770/IP.Cameras/IPC.Upgrade%20Software.N18A_1_2_2_561120B14.version.7z
I found it at this websitehttp://www.tv2211.com/en/NewsShow.asp?ID=677, but it seems to be down for the last few days. I was searching for "Juan Firmware", which some of the files I FTP'd from the camera had mentioned and came across that Chinese site and found a few downloads.
Thank you for your response...

8
Hacking & Modding / Reset jumper pins
« on: April 29, 2014, 11:51:04 am »
I have a generic bullet IP camera, marked as Vanxse, Model V-B811; it is similar to others with different names on it from different sellers or outlets.
It has Hi3518 chip board (pictures attached). nMap scan lists it as D-Link DSC-932L.
I've lost access over http port, nMap scan show only ports: 21, 23 and 5050 (still trying Telnet access, but there are too many possibilities of name/pswd).
I'm trying to reset the camera to factory settings, but there is no reset lead/switch.
I was wondering if anyone knew which jumper(s) on the pc board are the reset contacts.
Any help would be greatly appreciated.
./B

9
Hacking & Modding / Re: Looking for replacement glass
« on: April 28, 2014, 07:39:26 pm »
There is no help from the eBay seller, that's why I have been looking around.
There has to be some shop somewhere who sells different parts like this...

10
Hacking & Modding / Looking for replacement glass
« on: April 25, 2014, 07:49:29 pm »
Where can one find replacement part for the security cameras?
Specifically, I'm looking for replacement glas/lens for a bullet type outdoor IP camera (generic china, listed as Vanxse V-B811)
The outer diameter of the glass is 50.40mm with a 18.95mm sensor lens insert in the middle.

I've searched around the interwebs, but did not find any place that would sell just the glass.
Any suggestion would be greatly appreciated.
./b

11
Hacking & Modding / Re: Telnet password and username for IPC
« on: April 22, 2014, 08:59:27 pm »
Pictures of the board



12
Hacking & Modding / Re: Telnet password and username for IPC
« on: April 22, 2014, 08:56:33 pm »
I have the same (?) camera, at least by the outside looks, bought here: http://www.ebay.com/itm/CCTV-IR-1080X720P-1-0MP-HD-P2P-outdoor-3-6mm-Onvif-network-Security-IP-Camera-/111245655784?pt=US_Security_Cameras&hash=item19e6c1fee8
My camera is labelled as: Vanxse Model V-B811, but I've seen many variants, as far a Vendor and Model numbers go, on different reseller sites.
I lost access to web interface on port 80, nmap scan shows only ports: 21 (ftp), 23 (telnet) and 5050 (multimedia conference control tool) open on the camera. Can't access with Telnet, wrong username and/or password, but I was able to pull some files with FTP. There were the two directories listed, "/conf" and "/custom" (can send via PM), which do not mean a whole lot to me. Poked around some of the ".html" files, but did not find anything of use. Seems like most of the configuration is saved in ".json" files.
The reseller did not provide any files or directions upon request (get what you pay for...)
Camera goes apart fairly easily, just carefully unscrew the body (threads are under the ring), paying attention not to mess up the wiring inside.
This is what is printed on the board: Hi3518_OV9712_v2.2.3_SQ38, which tells me it has a Hi3518 chip with OV9712 CMOS, version 2.2.3 (?) and whatever SQ38 is...
Will post some pictures of the board later on today...
Hope to get some more good info sharing going on here.
./b

Pages: [1]