Registered a URL and setup a forum as the IPCam stuff really needed its own site vs my irregular blog posts about IPCam hacking at

Recent Posts

Pages: 1 ... 8 9 [10]
Hacking & Modding / Re: Zosi ZG2622MW partition addresses
« Last post by admin on May 14, 2020, 06:55:14 am »
If you've nuked the uboot, will need an spi flasher or similar to reflash.

Have a look at the forums for routers eg (dd/open)wrt, as people do that a lot, and its described in more detail than I'm willing to type :)

Hacking & Modding / Zosi ZG2622MW partition addresses
« Last post by arievh on May 12, 2020, 04:51:05 pm »
So connected my working IPCAM with UART
Want to download the 16mb with tftp for my birkced cam, but i Don't know the adresses.

I have this information:
Creating 4 MTD partitions on "hi_sfc":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000000f80000 : "rootfs"
0x000000f80000-0x000001000000 : "config"

so the boot download goes a little something like this:
sf read 0x82000000 0 0x100000
tftp 0x82000000 mtdblock0 0x100000

sf read 0x82000000 0x100000 0x400000
tftp 0x82000000 mtdblock1 0x400000

Rootfs: fails with this:
sf read 0x82000000 0x400000 0xf80000
tftp 0x82000000 mtdblock2 0xf80000

It says something like out of range...
SO i guess i don't know the address..

I have to say I'm new at this IPCAM stuf.. just started yesterday to explorerand fool arround (also bricked 2 ip cameras cause I wrote to the boot sector (uboot)woops! Any way to put a new uboot on those?


General Discussion / NVSIP SAF-980
« Last post by Marasmius on May 09, 2020, 05:44:15 pm »
Please help identify and find the firmware for the camera:
The site indicated on the camera body:
General view of the camera:

Photo of the camera board:
Open ports: 80,211.9101
Telnet is accessible through port 211, the login and password do not match those that were set during configuration through the NVSIP application and through the browser (it works only with the ActiveX extension).
If possible, help me change the password for telnet and / or where to solder the TTL-USB interface converter or flash the camera in another way (if available, firmware from a more stable model with the same equipment).
General Discussion / EZVIZ C2C (Mini O)
« Last post by Marasmius on May 09, 2020, 05:38:11 pm »
Good day, please help me find the firmware for EZVIZ C2C (Mini O) (Rostelecom CS-C2SHW) and pinout for connecting UART.
I got a camera stitched by Rostelecom, I would like to return the camera to the original firmware.
If possible, describe the process in more detail, because I come across cameras for the first time.
Help / Re: Sannce 960p Wifi IP Camera - Alternate firmware?
« Last post by kxn on May 03, 2020, 10:21:02 am »
Thank you for the password, its woking.

Are you still in to this?

I have the K9604-W DVR system with 4 ipcs
Have you managed to update an alternativ Firmware?

I would be very interestet in your findings.

Reg Konrad
Help / wrong firmware?
« Last post by mrmacc on April 07, 2020, 05:18:17 pm »
hallo i need help.
i have KKMOON NVR+PoE and i ahd V4.02.R11.E82B0119.12001.130000.00000
Build date 08.08.2017

i have upgrade 2018-05-21 FileName SimpGeneral_General_NBD6808T-PL_V4.02.R11.20140723_NT
but now dont work. is there any solution? now i have only boot logo.
Help / IP Camera VS-SQ2-4G WIFI password
« Last post by jimek70 on February 05, 2020, 01:42:56 pm »
I have problem with IP Camera.
Is there any chance to change AP WIFI password in camera ?
I tried to do it through the browser and the IP address but after the change was still the old WIFI password: 1234567890.
Is there any way to change this password?
Otherwise, after connecting the camera, the neighbors will be able to connect to my camera via WIFI and browse the internet via my camera sim card.
Please help ...
Pages: 1 ... 8 9 [10]