News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - novasat

Pages: [1]
1
Firmware / Maygion mips MJPEG ipcam MAC address
« on: March 22, 2016, 10:15:17 am »
2 Maygion mips MJPEG   ipcam with the same MAC address
I need to know where MAC address is located and how can we change it?


2
Help / Re: Two MAYGION mips MJPEG ipcam with the same MAC address
« on: March 12, 2016, 02:21:07 pm »
huh   

3
Help / Re: Two MAYGION mips MJPEG ipcam with the same MAC address
« on: March 10, 2016, 11:24:46 am »
Code: [Select]
BusyBox v1.12.1 (2012-01-09 07:05:43 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# ls -la
-rw-r--r--    1 0        0             789 Mar  6 13:01 ldr.ini
-rwxr-xr-x    1 0        0              61 Jan  1  2000 init.sh
drwxr-xr-x    3 0        0               0 Mar  8 15:49 www
-rwxr-xr-x    1 0        0          145844 Jan  1  2000 ldr
drwxr-xr-x    2 0        0               0 Mar  8 23:05 app
-rwxr-xr-x    1 0        0          141632 Apr 17  2011 fd
drwxr-xr-x    5 0        0               0 Jan  1  2000 ..
drwxr-xr-x    5 0        0               0 Jan  1  1970 .
#

i changed ldr and ldr.ini  but MAC  and WIFI MAC are still  the same .

4
Help / Two MAYGION mips MJPEG ipcam with the same MAC address
« on: March 10, 2016, 10:08:27 am »
2 Maygion mips MJPEG   ipcam with the same MAC address
I need to know where MAC address is located and how can we change it?

5
Firmware / Re: Help needed, my new IP Cam MP-3.3 with WPS is dead
« on: November 04, 2013, 08:16:19 pm »
  >:( >:( :-[

6
Firmware / Re: Help needed, my new IP Cam MP-3.3 with WPS is dead
« on: May 19, 2012, 11:47:00 am »
To Admin
Please help me to understand what is going on with this product.
Is it the processor MIAGLE600?
Is it the Flash memory?

The electronic parts are not  so many,and I have the possibility to replace any of the known parts even BGA.

I will try to put here data sheets of parts as soon as I found them.

1- uPD45128163G5-A75LI-9JF.       ELPIDA   SDRAM.    U3
   ---> 128M-bit Synchronous DRAM  4-bank, LVTTL  WTR (Wide Temperature Range)
   http://www.elpida.com/eolpdfs/E0346N10_EOL.pdf
2- ULN2803AG.         U1
   ---> 8ch high voltage high current darlington array
   http://www.sycelectronica.com.ar/semiconductores/ULN2803-SMD.pdf
   http://www.rentron.com/Files/uln2803.pdf
3- H1102NL Pulse.    T1
    ---> 10/100BASE-T SINGLE PORT SURFACE MOUNT MAGNETICS
    http://ww2.pulseeng.com/products/datasheets/H325.pdf
4- WM8988L.             
    ---> Low power high quality stereo CODEC
    http://www.wolfsonmicro.com/documents/uploads/data_sheets/en/WM8988.pdf
5- FR9886D.                U5
    ---> Synchronous step-down DC/DC converter
    http://www.hongoda.com/upload/Image/EYkqr4.pdf
6- RT5350F   APSoC        U7    (Etched by Laser)
    ---> World’s Smallest Integrated Wireless Router-on-a-chip
    SoC  means "System on Chip"
    http://www.ralinktech.com/en/02_products/product.php?sn=1005

     The BGA size is 12x12 mm and pitch 0.8mm or a total of 196 balls (14x14).


      M1AGLE600  IGLOOe
---> Developed by ARM in collaboration with Actel, the 32-bit ARM Cortex™-M1 processor is the first ARM processor designed for FPGA implementation. With a balance between size and speed, the free Cortex-M1 processor operates at up to 60 MHz and can be implemented in as few as 4,353 tiles.
      http://www.actel.com/documents/IGLOOe_DS.pdf
      http://www.actel.com/documents/IGLOOe_UG.pdf
      http://www.actel.com/documents/CortexM1_PB.pdf
      http://www.actel.com/products/igloo/docs.aspx#ds



Finaly I could read what was written on the BGA before it was ETCHED by LASER, hope this can help.



   Mine is
Ralink
RT5350F
PAN6700409
1142STA1



    I can't find datasheet for RT5350F but the RF3050 is similar.
 http://dl.dropbox.com/u/55442241/My%20IP%20Camera/RT3050_5x_V2.0_081408_0902.pdf
   
    The SDK for the RT5350 can be obtained from gitorious:
    http://gitorious.org/wive-rtnl-ralink-rt305x-routers-firmware
    SDK means "Software Development Kit"

7- MX25L3206E   Macronix    U9     (Etched by Laser)
    --->32M-BIT [x 1 / x 2] CMOS SERIAL FLASH   8-PIN SOP  "Small Outline Package"
  http://dl.dropbox.com/u/55442241/My%20IP%20Camera/MX25L3206E%2C%203V%2C%2032Mb%2C%20v1.4.pdf


If any one has a comment please don't hesitate.
Excuse my English is not so good.
Regards

7
Firmware / Help needed, my new IP Cam MP-3.3 with WPS is dead
« on: May 13, 2012, 08:39:41 am »

press for a large picture


press for a large picture


press for a large picture

Hello ALL
Only after a week the camera was not responding or some times yes and many times no .
Normally when you press the WPS button you got a blue led at the back near the wps switch that fliker until you have a connection with the router then it turn off.
Before camera died the wps button was not responding.

After that the camera went  hot. I open it and I found the horizontal stepper motor and the power driver IC ULN2803 at the bottom of the camera very hot.
I remove the motor socket and the ic ULN2803 cool down with the main power on.
I think the main problem is with firmware.

I bought another camera and in less than a week the same scenario happen again.
What I was sure of is that the camera was connecting on IP 192.168.1.111 but now the router is not seeing the camera.
I tried FTP but no luck.
If any one can help with this hardware MP-3.3 , this will be great.
Thanks

Pages: [1]