Registered a URL and setup a forum as the IPCam stuff really needed its own site vs my irregular blog posts about IPCam hacking at

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - m0rfy

Pages: [1]
Help / Re: Open video divice error
« on: February 14, 2014, 09:08:13 am »
No help?? =(

Firmware / Re: Firmware for EasyN FS-603A-M106
« on: December 18, 2013, 01:13:30 pm »
Hi, im has bricked my camera, when i flash new firmware, my camera doesn't work, no self test, and no conect. How i can repair it?
  so now when you connect your camera with cable and power adapter,and the camera cant do self-test,right,and the two lights near by the LAN cable,whether one light is blinking,one light is bright.of course,if you really need to do maintain,you can contact the business  personnel who will support the corresponding procedure about this.

How I can contact him? Or where I can find him? I tried to reboot Linux and romfs with j2tag, but it not help, I think I can't find good Linux and romfs.
  please contact the one who sell you the hope you can understand.

I can't, I didn't know who seller, it's a gift. Why you cannot help me?
  how do i help you.cause it is the problem of hardware,so if there is something i can do for you,i'm ready to help you.but currently,if it is the problem hardware,i don't know how to help you.cause the camera need to be maintained and checked.

Ok, can you please send me good framework with linux, romfs and boot info?
   sorry,i couldn't do that.and those information is our company's develop program,do hope you can understand.

Help / Re: Open video divice error
« on: November 01, 2013, 07:31:27 pm »
After reading the forums, it seems a power problem, namely the "5 +" does not come at the camera.
Who knows the circuit board?
Or how to power from another place on the board?

Help / Re: Open video divice error
« on: November 01, 2013, 06:41:06 pm »
Well, I noticed that the change of different linux and romfs it doesn't help...
As I understand it is not enough of something else

Help / Open video divice error
« on: November 01, 2013, 05:41:51 pm »
W90P745 Boot Loader [ Version 1.1 $Revision: 1 $ ] Rebuilt on May 11 2010
Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes
Board designed by Winbond
Hardware support provided at Winbond
Copyright (c) Winbond Limited 2001 - 2006. All rights reserved.
Boot Loader Configuration:

        MAC Address         : 00:B8:00:00:68:D2
        IP Address          :
        DHCP Client         : Enabled
        CACHE               : Enabled
        BL buffer base      : 0x00300000
        BL buffer size      : 0x00100000
        Baud Rate           : 115200
        USB Interface       : Enabled
        Serial Number       : 0xFFFFFFFF

For help on the available commands type 'h'

Press ESC to enter debug mode ......
Cache enabled!
Processing image 1 ...
Processing image 2 ...
Processing image 3 ...
Processing image 4 ...
Processing image 5 ...
Processing image 6 ...
Processing image 7 ...
Unzip image 7 ...
Executing image 7 ...
Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0) #1453 Ò» 12ÔÂ 6
 08:30:46 CST 2010
Processor: Winbond W90N745 revision 1
Architecture: W90N745
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 rw
Calibrating delay loop... 39.83 BogoMIPS
Memory: 16MB = 16MB total
Memory: 14320KB available (1481K code, 299K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
PTZ Driver has been installed successfully.
Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no serial options en
ttyS00 at 0xfff80000 (irq = 9) is a W90N745
Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no serial options e
ttyS00 at 0xfff80100 (irq = 10) is a W90N7451
I2C Bus Driver has been installed successfully.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 7F0E0000-7F1EBFFF [VIRTUAL 7F0E0000-7F1EBFFF] (RO)
S29GL032N Flash Detected
01 eth0 initial ok!
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
Winbond Audio Driver v1.0 Initialization successfully.
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 15
usb-ohci.c: AMD756 erratum 4 workaround
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4

 _____     ____    _    ____
|__  /   _|  _ \  / \  / ___|
  / / | | | | | |/ _ \ \___ \
 / /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/   \_\____/
ZD1211B - version
usb.c: registered new driver zd1211b
main_usb.c: VIA Networking Wireless LAN USB Driver 1.20.04
usb.c: registered new driver vntwusb
usb.c: registered new driver rt73
dvm usb cam driver by Maverick Gao in 2010-8-3
usb.c: registered new driver dvm
dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20
usb.c: registered new driver dvm usb cam driver for sonix288
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 40K
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
Shell invoked to run file: /bin/init
Command: mount -t proc none /proc
Command: mount -t ramfs none /usr
Command: mount -t ramfs none /swap
Command: mount -t ramfs none /var/run
Command: mount -t ramfs none /etc
Command: mount -t ramfs none /flash
Command: mount -t ramfs none /home
Command: mount -t ramfs none /tmp
Command: mkdir /tmp/run
Command: camera&
Command: sh

Sash command shell (version 1.1.1)
/> no support
hub.c: connect-debounce failed, port 1 disabled
new USB device :80fb4004-fed740
hub.c: new USB device 1, assigned address 2
usb.c: USB device 2 (vend/prod 0x148f/0x3070) is not claimed by any active drive
new USB device :80fb4204-fed740
hub.c: new USB device 2, assigned address 3
p1[7]:1,j 3,config->bNumInterfaces:4
usbaudio: device 3 audiocontrol interface 2 has 1 input and 0 output AudioStream
ing interfaces
usbaudio: valid input sample rate 48000
usbaudio: device 3 interface 3 altsetting 1: format 0x00000010 sratelo 48000 sra
tehi 48000 attributes 0x01
usbaudio: registered dsp 14,35
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at 00ff3ba0
factory params zone not inited !
camera params zone not inited !

sw version is
factory video params zone not inited !
video params zone not inited !
dyndns status zone not inited !
preset params zone not inited !

aw version is

Wait for auto-negotiation complete...OK
100MB - FULL
open video device error

what can i do? pls help
on box marked F-m166
on board marked m136
how to repair? =(

Pages: [1]