News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Author Topic: CoolCam NIP-02, different versions, need help  (Read 96139 times)

  • ***
April 12, 2014, 10:24:26 am
My camera is well restored I connected the camera trow wireless, no wire to camera, I go to your link, and put this string:
192.168.1.8:81/videostream.cgi?

I have not the ddns
I logged successful to camera and opened your link, then appear the login popup, I put my user like camera window, but this popup appear again, I reput my user but nothing, this is like wrong user. Perhaps I have to add a password to the standard admin?

What is happening when you enter the user does it keep prompting you to enter the user again?

If so then yes, please add a password to Admin and try agaim.

Don

  • No avatar
  • *
April 12, 2014, 10:38:19 am
Nothing nothing nothing... I uses admin admin, nothing I put it 2-3 times... please kindly man, do a miracle to this camera... :-(

  • ***
April 12, 2014, 10:40:34 am
Nothing nothing nothing... I uses admin admin, nothing I put it 2-3 times... please kindly man, do a miracle to this camera... :-(

Please contact your seller to see what they say could be the issue? Also ask them for the CGI SDK for commands for your camera as well.

In most cases your seller will be helpful.

Don

  • No avatar
  • *
April 12, 2014, 10:55:23 am
I found some sdk commands trow ispy... However I hope that the site that I contacted can help me... thank youv ery much for your help...

  • ***
April 12, 2014, 10:56:52 am
I found some sdk commands trow ispy... However I hope that the site that I contacted can help me... thank youv ery much for your help...

You are very welcome.

Don

  • No avatar
  • *
April 13, 2014, 09:48:24 am
Hello Don, I am reading this document:
http://foscam.us/forum/free-generic-browser-interface-for-foscam-mjpeg-ptz-cameras-t2522.html

I read that I can download your online "Hack", so I'll test it in local. I think that it can be a good idea. I'll stay in touch with you. Many thanks for your free mod. Cheers..

  • ***
April 13, 2014, 09:59:53 am
Hello Don, I am reading this document:
http://foscam.us/forum/free-generic-browser-interface-for-foscam-mjpeg-ptz-cameras-t2522.html

I read that I can download your online "Hack", so I'll test it in local. I think that it can be a good idea. I'll stay in touch with you. Many thanks for your free mod. Cheers..

You are very welcome.

Please note. It's NOT a "Hack"

Valid, approved and supported CGI commands are being used with the Interface:

http://foscam.us/forum/cgi-api-sdk-for-mjpeg-h-264-camera-t2986.html#p13630

So the Interface is based on approved methods and NOT hacks.

Don
« Last Edit: April 13, 2014, 11:32:37 am by TheUberOverLord »

  • No avatar
  • *
July 22, 2014, 03:53:00 am
Hello Everybody,

I got the updates (firmware & Web UI) from the support of www.szneo.com

I apply it and it fix the movement detection bug, which doesn't worked before.

I attached the updates in a .zip

It's only for neo coolcam nip-02 with current firmware starting with "81.2"

I hope it will be usefull for somebody!

  • No avatar
  • *
August 15, 2014, 09:39:32 am
@TheUberOverLord

I can't use GenericBIV31.htm, when I type password the screen gets blank. I only changed file to my local ip.

What can I do?

  • ***
August 15, 2014, 10:36:41 am
@TheUberOverLord

I can't use GenericBIV31.htm, when I type password the screen gets blank. I only changed file to my local ip.

What can I do?

I assume your IP Camera is a Foscam MJPEG based or Clone IP Camera?

Did you download the Interface from here?

http://foscam.us/forum/free-generic-browser-interface-for-foscam-ip-mjpeg-cameras-t2522.html

1. Please make sure you are NOT using a leading http:// when defining the DDNS or IP Address and port for your IP Camera in the Interface configuration.

2. Please make sure if you are attempting to access the camera remotely that you are using your ISP IP Address or DDNS and port for your IP Camera and not your local IP Address and port for the IP Camera.

You can also try this to instantly access your IP Camera from within your local network using the local IP Address or ISP IP Address or DDNS and port for your IP Camera or remotely using your ISP IP Address or DDNS and port for your IP Camera. Does it work?

http://www.saveontelephonebills.com/camera/YourCameraBIV25.htm

If it does? Then something is wrong with the configuration values you have setup in your copy of the Interface.

Don
« Last Edit: August 15, 2014, 11:00:25 am by TheUberOverLord »

  • No avatar
  • *
August 15, 2014, 11:58:14 am
@TheUberOverLord

I can't use GenericBIV31.htm, when I type password the screen gets blank. I only changed file to my local ip.

What can I do?

I assume your IP Camera is a Foscam MJPEG based or Clone IP Camera?

Did you download the Interface from here?

http://foscam.us/forum/free-generic-browser-interface-for-foscam-ip-mjpeg-cameras-t2522.html

1. Please make sure you are NOT using a leading http:// when defining the DDNS or IP Address and port for your IP Camera in the Interface configuration.

2. Please make sure if you are attempting to access the camera remotely that you are using your ISP IP Address or DDNS and port for your IP Camera and not your local IP Address and port for the IP Camera.

You can also try this to instantly access your IP Camera from within your local network using the local IP Address or ISP IP Address or DDNS and port for your IP Camera or remotely using your ISP IP Address or DDNS and port for your IP Camera. Does it work?

http://www.saveontelephonebills.com/camera/YourCameraBIV25.htm

If it does? Then something is wrong with the configuration values you have setup in your copy of the Interface.

Don

I have this "fake" Coolcam NIP-02, I tried your software with a EasyN Model M sometime ago and worked flawlessly.

Using local file I get only a blank screen after login and on your website only the ad "
Click For Cheap Website Cloud Hosting " shows after login.

Using TinyCam Monitor the cam is identified as "Medisana Smart Baby Monitor"  >:(

It's the only software, besides it's own one that works.

  • ***
August 15, 2014, 02:33:15 pm
@TheUberOverLord

I can't use GenericBIV31.htm, when I type password the screen gets blank. I only changed file to my local ip.

What can I do?

I assume your IP Camera is a Foscam MJPEG based or Clone IP Camera?

Did you download the Interface from here?

http://foscam.us/forum/free-generic-browser-interface-for-foscam-ip-mjpeg-cameras-t2522.html

1. Please make sure you are NOT using a leading http:// when defining the DDNS or IP Address and port for your IP Camera in the Interface configuration.

2. Please make sure if you are attempting to access the camera remotely that you are using your ISP IP Address or DDNS and port for your IP Camera and not your local IP Address and port for the IP Camera.

You can also try this to instantly access your IP Camera from within your local network using the local IP Address or ISP IP Address or DDNS and port for your IP Camera or remotely using your ISP IP Address or DDNS and port for your IP Camera. Does it work?

http://www.saveontelephonebills.com/camera/YourCameraBIV25.htm

If it does? Then something is wrong with the configuration values you have setup in your copy of the Interface.

Don

I have this "fake" Coolcam NIP-02, I tried your software with a EasyN Model M sometime ago and worked flawlessly.

Using local file I get only a blank screen after login and on your website only the ad "
Click For Cheap Website Cloud Hosting " shows after login.

Using TinyCam Monitor the cam is identified as "Medisana Smart Baby Monitor"  >:(

It's the only software, besides it's own one that works.

I am somewhat confused as to what you are saying? Are you saying that the link I gave you is also failing but that it has worked in the past?

http://www.saveontelephonebills.com/camera/YourCameraBIV25.htm

If so, have you changed ISP IP Addresses/DDNS Addresses or the port for your IP Camera or have you installed firmware for your IP Camera recently?

Don


  • No avatar
  • *
August 15, 2014, 03:16:11 pm
Using CoolCam NIP-02:

I tried the link you gave and only "Click For Cheap Website Cloud Hosting" shows after login.

Using GenericBIV31.htm, blank screen after login.

I can login using both ways (so the ip is correct).

--------------

Using EasyN Model M:

Works normal.

  • ***
August 15, 2014, 04:47:29 pm
Using CoolCam NIP-02:

I tried the link you gave and only "Click For Cheap Website Cloud Hosting" shows after login.

Using GenericBIV31.htm, blank screen after login.

I can login using both ways (so the ip is correct).

--------------

Using EasyN Model M:

Works normal.

Then the CoolCam NIP-02 does not use the same CGI commands as the Foscam MJPEG based IP Cameras or their Clones do. Because of that. The interface will not work with this specific IP Camera.

You may want to contact your seller and see if they will give you what's known as the "CGI SDK Manual" for this IP Camera model. If they will? Then it would be possible to implement something like this for this IP Camera brand and model as it would be for any other IP Camera brand and model that supports CGI commands and pulling snapshots from the IP Camera using HTTP or HTTPS access methods:

http://foscam.us/forum/a-how-to-embed-any-foscam-ip-camera-in-webpage-using-1-line-t9113.html#p43654

This would also allow you to display different IP Camera models and brands of IP Camera models, at the same time. Using any Internet browser capable device.

Live example here showing 14 different IP Cameras at the same time. That also allows each IP Camera to be viewed and/or controlled individually from ANY Internet browser capable devices. From Computers to Tablets and Phones to TVs. While all being done, totally securely, without the need to install any software on any device:

http://107.170.59.150/foscam/FoscamUS.htm

You can try the above example, from the Internet browser capable devices of your choice.

Don
« Last Edit: August 15, 2014, 05:54:51 pm by TheUberOverLord »

  • No avatar
  • *
August 19, 2014, 11:17:12 am
Hello Everybody,

I got the updates (firmware & Web UI) from the support of www.szneo.com

I apply it and it fix the movement detection bug, which doesn't worked before.

I attached the updates in a .zip

It's only for neo coolcam nip-02 with current firmware starting with "81.2"

I hope it will be usefull for somebody!

Hi Frud,

Could you explain the process to update the FW and the WebUI?
[Edit] I saw a message I wrote on first page of this discussion where I explain that it is possible from Windows App and Web UI, forget this silly request...

Mine is not a Coolcam, but have the following version, I'm not sure this FW will work fine, do you think that I have a risk of brick?
   Device Firmware Version      81.2.0.133
   Device Embeded Web UI Version      20.2.1.2.15
   Device ID      NIP-xxxxxx-CWFWW


Thanks

Yakka
« Last Edit: August 20, 2014, 12:13:53 pm by yakka »