Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Author Topic: Aldi / Supra Foto Elektronik Vertriebs GmbH - Maginon IPC 1  (Read 38693 times)

January 20, 2013, 08:00:05 pm
I recently purchased an IP Camera from Aldi Australia.

This appears to be running the OpenIPCam firmware with the JQuery/AJAX based variant of the UI.

For the most part it works, I've not tried it with the supplied Windows software, just directly configured via the web interface. The web interface seems to have a limit of 12 characters for passwords and will error if you try to enter a longer password. It also seems to leak things like the MAC address and name of the camera before one has authenticated.

Code: [Select]
Camera ID: **REDACTED**
Date and time: Mon 21 Jan 2013 11:13:25 EST
Firmware version:
Web interface version:
Camera name: **REDACTED**
Connection status: Wired
Alarm status: No alarm
DDNS status: No DDNS
UPNP status: No UPNP

It appears to be limited to MJPEG video, however it seems to have an undocumented audio feature as there's an audio socket on the back and outside of the standard web UI, if you load up:


... as documented on this site, you'll get a stream with audio. Microphone appears to be part of camera assembly. Audio very bad over WiFi, only works well on wired ethernet.

Does this look like a model that might benefit from newer versions of firmware?

January 20, 2013, 08:03:22 pm
Another board view

January 20, 2013, 08:04:28 pm
Final board view

January 20, 2013, 09:45:34 pm
Only web port is open..

Code: [Select]
# nmap -O -p1-65535 CAMERA

Starting Nmap 6.00 ( ) at 2013-01-21 11:42 EST
Nmap scan report for CAMERA
Host is up (0.0015s latency).
Not shown: 65534 closed ports
80/tcp open  http
MAC Address: CAMERAMAC (Unknown)
Device type: specialized|webcam
Running: AirMagnet embedded, Foscam embedded, Instar embedded
OS details: AirMagnet SmartEdge wireless sensor, or Foxcam FI8904 or Instar IN-3010 surveillance camera
Network Distance: 1 hop

OS detection performed. Please report any incorrect results at .
Nmap done: 1 IP address (1 host up) scanned in 35.73 seconds[/code

Oh, and there's another chip under the WiFi board, but the WiFi board is soldered in place.
« Last Edit: January 20, 2013, 09:52:57 pm by ADFHogan »

March 16, 2013, 01:57:11 pm
Web interface update for the Maginon IPC-1 is here:

German (DE):
English (AU):

Actual files inside the ZIPs seems to be the same (byte for byte when extracted) for de-DE and en-AU pages.
« Last Edit: March 16, 2013, 02:11:26 pm by ADFHogan »

September 18, 2013, 07:08:44 am

There seems to be another Homepage with even newer Firmware + new Webinterface :

These Files extract to :
ipc_2240_supra_ipc1.bin from 23.July 2013 -> Webinterface Version
lr_cmos_0_41_2_51.bin from 22.July 2013 -> Firmware Version

I have successfully flashed these two files into my camera.

September 19, 2013, 10:30:44 am

There seems to be another Homepage with even newer Firmware + new Webinterface :
Also found similar page through same site with same firmware but English documentation.

Doesn't seem to be any obvious difference, and audio feature still works if you access feed via:


... as documented in the IPCAM CGI SDK 2.1 PDF. Is there a changelog somewhere?