News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Poll

Problem firmware

ip camera
0 (0%)
problem
0 (0%)

Total Members Voted: 0

Voting closed: September 10, 2012, 12:52:29 PM

Author Topic: Wanscam AJ-C2WA-C118 Help  (Read 5560 times)

July 22, 2012, 12:52:29 PM
I buy http://www.wanscam.com/product/product_show_24707.html on ebay

Camera had no option DDNS: no-ip

i flash new firmware Foscam FI8908W Firmware 11.22.2.30  all ok

i flash  firmware FI8908W_Firmware_11_14_2_17__UI_2_4_8_14  and camera died

i have USB to serial UART

and read state http://www.gadgetvictims.com/2009/12/bring-your-fi8908w-paperweight-back-to.html

but have problem  when i rebooting i have problem
i flash adress  fx 6 romfs.img 0x7f0d0000 0x7f0d0000 -a  and  bootloader > fx 6 romfs.img 0x7f0e0000 0x7f0e0000 -a       but the problem remains

please help

my log

W90P745 Boot Loader [ Version 1.1 $Revision: 1 $ ] Rebuilt on May 11 2010
 Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes
 Board designed by Winbond
 Hardware support provided at Winbond
 Copyright © Winbond Limited 2001 - 2006. All rights reserved.
 Boot Loader Configuration:

 MAC Address : 00:D6:FB:00:BC:9F
 IP Address : 0.0.0.0
 DHCP Client : Enabled
 CACHE : Enabled
 BL buffer base : 0x00300000
 BL buffer size : 0x00100000
 Baud Rate : -1
 USB Interface : Disabled
 Serial Number : 0xFFFFFFFF


 For help on the available commands type 'h'

 Press ESC to enter debug mode ......
 Cache enabled!
 Processing image 1 ...
 Processing image 2 ...
 Processing image 3 ...
 Processing image 4 ...
 Processing image 5 ...
 Processing image 6 ...
 Processing image 7 ...
 Unzip image 7 ...
 Executing image 7 ...
 Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0) #467 ¶þ 12ÔÂ 25
 19:24:28 CST 2007
 Processor: Winbond W90N745 revision 1
 Architecture: W90N745
 On node 0 totalpages: 2048
 zone(0): 0 pages.
 zone(1): 2048 pages.
 zone(2): 0 pages.
 Kernel command line: root=/dev/rom0 rw
 Calibrating delay loop... 39.83 BogoMIPS
 Memory: 8MB = 8MB total
 Memory: 6688KB available (1120K code, 198K data, 40K init)
 Dentry cache hash table entries: 1024 (order: 1, 8192 bytes)
 Inode cache hash table entries: 512 (order: 0, 4096 bytes)
 Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
 Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
 Page-cache hash table entries: 2048 (order: 1, 8192 bytes)
 POSIX conformance testing by UNIFIX
 Linux NET4.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3.039
 Initializing RT netlink socket
 Starting kswapd
 Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no serial options en
 abled
 ttyS00 at 0xfff80000 (irq = 9) is a W90N745
 I2C Bus Driver has been installed successfully.
 Blkmem copyright 1998,1999 D. Jeff Dionne
 Blkmem copyright 1998 Kenneth Albanowski
 Blkmem 1 disk images:
 0: 700000-6FFFFF [VIRTUAL 700000-6FFFFF] (RO)
 No supported flash detected!
 01 eth0 initial ok!
 which:0
 PPP generic driver version 2.4.2
 Linux video capture interface: v1.00
 SCSI subsystem driver Revision: 1.00
 Winbond Audio Driver v1.0 Initialization successfully.
 usb.c: registered new driver hub
 add a static ohci host controller device
 : USB OHCI at membase 0xfff05000, IRQ 15
 hc_alloc_ohci
 usb-ohci.c: AMD756 erratum 4 workaround
 hc_reset
 usb.c: new USB bus registered, assigned bus number 1
 hub.c: USB hub found
 hub.c: 2 ports detected
 usb.c: registered new driver audio
 audio.c: v1.0.0:USB Audio Class driver
 usb.c: registered new driver serial
 usbserial.c: USB Serial Driver core v1.4
 Initializing USB Mass Storage driver...
 usb.c: registered new driver usb-storage
 USB Mass Storage support registered.
 dvm usb cam driver 0.0.0.0 by Maverick Gao in 2006-8-12
 usb.c: registered new driver dvm
 main_usb.c: DVM Wireless LAN USB DVM_WL_U_2007_A Driver 1.2 upgrade in 2007-2-5
 usb.c: registered new driver DVM Wireless LAN USB DVM_WL_U_2007_A
 NET4: Linux TCP/IP 1.0 for NET4.0
 IP Protocols: ICMP, UDP, TCP
 IP: routing cache hash table of 512 buckets, 4Kbytes
 TCP: Hash tables configured (established 512 bind 1024)
 Blkmem: bad access: block=0, count=1 (pos=200, len=0)
 end_request: I/O error, dev 1f:00 (Blkmem), sector 0
 FAT: unable to read boot sector
 Blkmem: bad access: block=0, count=1 (pos=200, len=0)
 end_request: I/O error, dev 1f:00 (Blkmem), sector 0
 FAT: unable to read boot sector
 Blkmem: bad access: block=0, count=2 (pos=400, len=0)
 end_request: I/O error, dev 1f:00 (Blkmem), sector 0
 romfs: unable to read superblock
 Kernel panic: VFS: Unable to mount root fs on 1f:00
 à


August 05, 2012, 03:32:14 PM
Hi, I have same this problem. I testing much ROMs Linux but much times i2c write error and reboot .. :( i need help thanks

  • No avatar
  • *****
August 10, 2012, 03:59:31 PM
Your kernel looks ok, but your romfs isn't in the right place.

You have a 4M flash camera, so suggest check the wiki or other posts for where you need to stick the romfs in flash memory.

kernel is ok, its the romfs you need to rewrite at the correct location.

See:
http://wiki.openipcam.com/index.php/Layout_in_Flash.




August 28, 2012, 11:50:15 AM
I also getting the same problem as you  :-\

Camera had no option DDNS: no-ip

So what happened ?? do you fix that ? Does your IP camera working with no-ip DDNS ?? Please reply me  :-\ I also having this damn problem.. Thank you

September 13, 2012, 09:40:31 AM
For ckalana

To have NO-IP listed on the camera ddns setting list, you shall need to update the Embedded WEB IU to version 0.9.4.17.
You do not need to update the firmware.

To get this you can email support at wanscam.com or email me.

Hope this helps
Jeff