News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Author Topic: Instar 3010 from 2011  (Read 387 times)

  • No avatar
  • *
August 14, 2017, 03:20:39 pm
hello everybody,
lets have some time travel back to 2011, i have such an old cam i wanna debrick after the Instar Website gave me a faulty firmware and brick it.

I am connected to my cam via serial and i lurked a long time on this board and tried a lot of suggestions for similar problems here.

But my cam always reboot.

Thats what the Bootloader told me:

Quote
W90P745 Boot Loader [ Version 1.1 $Revision: 1 $ ] Rebuilt on May 11 2010
Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes
Board designed by Winbond
Hardware support provided at Winbond
Copyright (c) Winbond Limited 2001 - 2006. All rights reserved.
Boot Loader Configuration:

        MAC Address         : 00:0D:C5:D2:C5:A5
        IP Address          : 0.0.0.0
        DHCP Client         : Enabled
        CACHE               : Enabled
        BL buffer base      : 0x00300000
        BL buffer size      : 0x00100000
        Baud Rate           : 115200
        USB Interface       : Enabled
        Serial Number       : 0x00BC614E


For help on the available commands type 'h'

Press ESC to enter debug mode ......
Cache enabled!
Processing image 1 ...
Processing image 2 ...
Processing image 3 ...
Processing image 4 ...
Processing image 5 ...
Processing image 6 ...
Processing image 7 ...
Unzip image 7 ...
Executing image 7 ...
Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0) #1925 Áù 11ÔÂ 3 04:41:51 CST 2012
Processor: Winbond W90N745 revision 1
Architecture: W90N745
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 rw
Calibrating delay loop... 39.83 BogoMIPS
Memory: 16MB = 16MB total
Memory: 14316KB available (1493K code, 292K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
PTZ Driver has been installed successfully.
Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no serial options enabled
ttyS00 at 0xfff80000 (irq = 9) is a W90N745
Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no serial options enabled
ttyS00 at 0xfff80100 (irq = 10) is a W90N7451
I2C Bus Driver has been installed successfully.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 7F0E0000-7F16BFFF [VIRTUAL 7F0E0000-7F16BFFF] (RO)
S29GL032N Flash Detected
01 eth0 initial ok!
which:0
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
i2s audio probe 1
Winbond Audio Driver v1.0 Initialization successfully.
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 15
hc_alloc_ohci
usb-ohci.c: AMD756 erratum 4 workaround
hc_reset
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4

 _____     ____    _    ____
|__  /   _|  _ \  / \  / ___|
  / / | | | | | |/ _ \ \___ \
 / /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/   \_\____/
     |___/
ZD1211B - version 2.24.0.0
usb.c: registered new driver zd1211b
main_usb.c: VIA Networking Wireless LAN USB Driver 1.20.04
usb.c: registered new driver vntwusb
usb.c: registered new driver rt73
dvm usb cam driver 0.0.0.1 by Maverick Gao in 2010-8-3
usb.c: registered new driver dvm
dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20
usb.c: registered new driver dvm usb cam driver for sonix288
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 40K
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
Shell invoked to run file: /bin/init
Command: mount -t proc none /proc
Command: mount -t ramfs none /usr
Command: mount -t ramfs none /swap
Command: mount -t ramfs none /var/run
Command: mount -t ramfs none /etc
Command: mount -t ramfs none /flash
Command: mount -t ramfs none /home
Command: camera&
[8]
Command: sh

Sash command shell (version 1.1.1)
/> hub.c: connect-debounce failed, port 1 disabled
new USB device :80fd5e04-fed740
hub.c: new USB device 1, assigned address 2
detect_sensor: mi360
dvm cmos successfully initialized
dvm camera registered as video0
aw version is 0.25.2.6
aw version is 3.16.2.51

Wait for auto-negotiation complete...OK
100MB - FULL
video0 opened
1
1
1
1
1
1
set resolution 4
set brightness 100
set contrast 4
set sharpness 3
set mode 0
__pthread_initial_thread_bos:35c000
manage pid:14
2
2
2
2
2
2
inet_sr.c INET_rinput 321
action===1
options==33
inet_sr.c INET_setroute 75
*args===255.255.255.255
*args===netmask
*args===eth0
[25]
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
write i2c error
myreboot

i tried an endless number different zips, bins and img´s but it will always come to:
[25]
10 time i2c write error
myreboot.

i get mad about this.

Could anyone explain me what does the [25] means?
I see some peolpes struggling with similar problems sometimes the number is [28] or whatever.

please explain, im sad.