News:

Re-organized the forum to more cleanly delineate the development section, as the end user support side appears to have taken a life of its own!

Author Topic: EasyN H3-V10R wifi driver FR4020A3  (Read 14774 times)

  • No avatar
  • *
August 21, 2015, 04:57:33 am
The wifi on my EasyN H3-V10R camera keeps crashing randomly after a few minutes to an hour. The output of the UART output pasted below indicates that it's a software problem: "Warning: Driver for device ra0 has been compiled with version 22 of Wireless Extension, while this program supports up to version 20. Some things may be broken..."
The camera runs a GM8125 ARM5 chip, the wifi module is FR4020A3 (not the ...A2).
Does anyone have a working wifi driver for this module and processorHHFAKV?
Needless to say that the EasyN helpdesk is of no help at all.

Quote
MP SPI-NOR Bootstrap v0.2
Boot image offset: 0x10000. Booting Image .....
0567Will set the following freq...
PLL1: 800 MHz, PLL2: 540 MHz, CPU freq: 540 MHz, AHB freq: 270 MHz, DDR freq: 800 MHz
go...

*********************************************
Please input Space to run Linux
Please input ESC to run UBOOT
Please input . to run burn-in
Otherwise, system will run Linux after 1 sec
*********************************************
Load image from SPI-NOR offset 0xd0000 to sdram 0x4000000
Jump 0x4000000
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.28 (root@gm8126.localdomain) (gcc version 4.4.0 (Faraday C/C++ Compiler Release 20100325) ) #175 PREEMPT Wed Jul 24 10:05:05 HKT 2013
CPU: FA626TE [66056261] revision 1 (ARMv5TE), cr=0000797f
CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
Machine: Faraday GM8126
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: mem=128M console=uart,shift,2,io,0xF9830000,38400
Early serial console at I/O port 0xf9830000 (options '38400', shift 2)
console [uart0] enabled
PID hash table entries: 512 (order: 9, 2048 bytes)
IC: GM8128 MP
GM Clock: CPU = 540 MHz, AHBCLK = 270 MHz, PLL1CLK = 800 MHz, PLL2CLK = 540 MHz
console handover: boot [uart0] -> real [ttyS0]
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 122708KB available (3677K code, 355K data, 2984K init)
Calibrating delay loop... 532.48 BogoMIPS (lpj=266240)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
Fmem: node 0 is online, alloc pages = 8192(active pages = 32768)
high_memory:0xc8000000, VM Start:0xc8800000, End:0xe0000000
NET: Registered protocol family 16
PMU: Mapped at 0xf9900000
pmu_get_cpu_clk:221 <fclk_mode=2, pll2_out=540000000>
Attach GM AHB-DMA Driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
Video Timer(timer3) Max 31000ms in 0xf9720840 HZ.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 239
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
probe ftgpio010.0 OK!!, at c8858000
probe ftgpio010.1 OK!!, at c885c000
probe ftgpio010.2 OK!!, at c8860000
Serial: 8250/16550 driver 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xf9830000 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xf9840000 (irq = 10) is a 16550A
serial8250: ttyS3 at I/O 0xf9880000 (irq = 21) is a 16550A
brd: module loaded
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Linux video capture interface: v2.00
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
Creating 6 MTD partitions on "wb_spi_flash":
0x000d0000-0x005ff000 : "Linux Section"
0x00600000-0x01000000 : "User Section"
0x00001000-0x00010000 : "Loader Section"
0x00010000-0x000b0000 : "BurnIn Section"
0x000b0000-0x000ce000 : "UBoot Section"
0x000ce000-0x000d0000 : "CFG Section"
Probe FTSSP010 SPI Controller at 0x98200000 (irq 6)
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
AMBA bus_register ok
Enter Device A
temp = 340
Drive Vbus because of ID pin shows Device A
otg2xx device_register ok
AMBA_bus_match(...) Found Driver FOTG2XX_DRV
AMBA_bus_match(...) Found Driver FOTG2XX_DRV
FOTG2XX_DRV fotg2xx_dev: GM  USB2.0 Host Controller
FOTG2XX_DRV fotg2xx_dev: new USB bus registered, assigned bus number 1
FOTG2XX_DRV fotg2xx_dev: irq 4, io mem 0xf9220000
FOTG2XX_DRV fotg2xx_dev: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FOTG200 Controller Initialization
fotg200 int enable = 1f30
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
ftiic010 ftiic010.0: irq 18, mapped at c886c000
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Freeing init memory: 2984K
usb 1-1: new high speed USB device using FOTG2XX_DRV and address 2
port status 10009
2nd port status 10009
***************************************
Busybox starts to run
***************************************
Mounting root fs rw ...
Mounting other filesystems ...
Setting hostname ...
Mounting user's MTD partion
FTMAC with FARADAY Internal PHY support
FTMAC110 Driver (Linux 2.6) 01/10/11 - (C) 2011 GM Corp.
reset Faraday Internal PHY.
ADDR: 00:64:03:00:12:51
ftmac110_link_change:2225 <SPEED100>
ftmac110_link_change:2239 <FULL>
usb 1-1: configuration #1 chosen from 1 choice
check..
rt5370sta: module license 'unspecified' taints kernel.
rtusb init rt3070STA --->


=== pAd = c89ce000, size = 528648 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
usbcore: registered new interface driver rt3070STA
------------[ cut here ]------------
WARNING: at mm/vmalloc.c:1159 __vunmap+0xf4/0x108()
Trying to vfree() nonexistent vm area (bf10c000)
Modules linked in: rtnet5370sta rt5370sta(P) rtutil5370sta ftmac100
[<c05bfb30>] (dump_stack+0x0/0x14) from [<c03085d8>] (warn_slowpath+0x64/0x80)
[<c0308574>] (warn_slowpath+0x0/0x80) from [<c03547ec>] (__vunmap+0xf4/0x108)
 r3:bf10c000 r2:c0638ff0
 r6:bf10c000 r5:00000000 r4:00000000
[<c03546f8>] (__vunmap+0x0/0x108) from [<c0354878>] (vfree+0x34/0x48)
 r7:0000a014 r6:00000000 r5:bf1098a0 r4:00000000
[<c0354844>] (vfree+0x0/0x48) from [<c02f96b4>] (module_free+0x14/0x18)
[<c02f96a0>] (module_free+0x0/0x18) from [<c0331d6c>] (sys_init_module+0xd8/0x18c)
[<c0331c94>] (sys_init_module+0x0/0x18c) from [<c02f5160>] (ret_fast_syscall+0x0/0x2c)
 r7:00000080 r6:beccef77 r5:00000002 r4:0000a014
---[ end trace 80c9307720c030bd ]---
i2c: 0x201200
sinit driver init successful!
mmc0: SDHCI controller on <NULL> [ftsdc010] using DMA
encript driver init successful!
infrared driver init successful!
relay driver init successful!
reset driver init successful!
rs485 driver init successful!
mmc0: new high speed SDHC card at address 1234
mmcblk0: mmc0:1234 SA04G 3.63 GiB
 mmcblk0: p1
ft-32ssp: common[ver:0.3.4] INIT OK!
card->cardno = 2
card->pbase = 98a00000
card->vbase = c8abe000
card->irq = 11
my_card->capture.dma_ch = 4
my_card->playback.dma_ch = 5
ft-32ssp: SoundCard(2) attached OK (c46309d0)
I2S probe ok in Slave mode.
Init SAR ADC done.
register sar adc device (0) OK!!
extalarm driver init successful!
wifikey driver init successful!
light driver init successful!
WDT base virtual address = c8ad8000
WDT base virtual address = c8adc000
wdt: default timeout: 5 sec.
wdt: default timeout: 20 sec.
(Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
RTMP_TimerListAdd: add timer obj c8a18930!
RTMP_TimerListAdd: add timer obj c8a18948!
RTMP_TimerListAdd: add timer obj c8a18960!
RTMP_TimerListAdd: add timer obj c8a18918!
RTMP_TimerListAdd: add timer obj c8a188d0!
RTMP_TimerListAdd: add timer obj c8a188e8!
RTMP_TimerListAdd: add timer obj c89e3364!
RTMP_TimerListAdd: add timer obj c89cffa4!
RTMP_TimerListAdd: add timer obj c89cffc4!
RTMP_TimerListAdd: add timer obj c89e33c0!
RTMP_TimerListAdd: add timer obj c89d279c!
RTMP_TimerListAdd: add timer obj c89d200c!
RTMP_TimerListAdd: add timer obj c89d2780!
RTMP_TimerListAdd: add timer obj c89d2a00!
RTMP_TimerListAdd: add timer obj c89d2818!
RTMP_TimerListAdd: add timer obj c89d2834!
RTMP_TimerListAdd: add timer obj c89d27b8!
RTMP_TimerListAdd: add timer obj c89d27d4!
RTMP_TimerListAdd: add timer obj c89d27f0!
RTMP_TimerListAdd: add timer obj c89e3334!
RTMP_TimerListAdd: add timer obj c89e33a4!
-->RTUSBVenderReset
<--RTUSBVenderReset
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
NVM is Efuse and its size =2d[2d0-2fc]
(Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
<7>Abnormal time diff = 12 ms
RTMPSetPhyMode: channel is out of range, use first channel=1
MCS Set = ff 00 00 00 00
<==== rt28xx_init, Status=0
0x1300 = 00064300
(Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
RTMP_TimerListAdd: add timer obj c8a18930!
RTMP_TimerListAdd: add timer obj c8a18948!
RTMP_TimerListAdd: add timer obj c8a18960!
RTMP_TimerListAdd: add timer obj c8a18918!
RTMP_TimerListAdd: add timer obj c8a188d0!
RTMP_TimerListAdd: add timer obj c8a188e8!
RTMP_TimerListAdd: add timer obj c89e3364!
RTMP_TimerListAdd: add timer obj c89cffa4!
RTMP_TimerListAdd: add timer obj c89cffc4!
RTMP_TimerListAdd: add timer obj c89e33c0!
RTMP_TimerListAdd: add timer obj c89d279c!
RTMP_TimerListAdd: add timer obj c89d200c!
RTMP_TimerListAdd: add timer obj c89d2780!
RTMP_TimerListAdd: add timer obj c89d2a00!
RTMP_TimerListAdd: add timer obj c89d2818!
RTMP_TimerListAdd: add timer obj c89d2834!
RTMP_TimerListAdd: add timer obj c89d27b8!
RTMP_TimerListAdd: add timer obj c89d27d4!
RTMP_TimerListAdd: add timer obj c89d27f0!
RTMP_TimerListAdd: add timer obj c89e3334!
RTMP_TimerListAdd: add timer obj c89e33a4!
-->RTUSBVenderReset
<--RTUSBVenderReset
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
NVM is Efuse and its size =2d[2d0-2fc]
(Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc]
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
<7>Abnormal time diff = 12 ms
RTMPSetPhyMode: channel is out of range, use first channel=1
MCS Set = ff 00 00 00 00
<==== rt28xx_init, Status=0
0x1300 = 00064300
BusyBox v1.13.4 (2013-07-02 22:11:21 HKT) multi-call binary

Usage: route [{add|del|delete}]

Edit kernel routing tables

Options:
        -n      Don't resolve names
        -e      Display other/more information
        -A inet Select address family

input_mode = 0
netflag.dat  sd           wifi.mac
netflag.dat  sd           wifi.mac
WDT base virtual address = c8ae0000

 RTC time 115-08-21 05:20:57
Set system time as date 08210520115.57.

Frammap: DDR0: memory base=0x4800000, memory size=0x2000000, alignment=4K
Frammap: version 0.28.3, 1 DDR is managed.

VideoGraph v0.44 You may use
   #echo 11 > /proc/videograph/dbg
to enable debug mode (0xbf1e250c)
Debug message at 0xc8b16000 start pointer 0xbf2025f0 size 0x124f80
killall: arping: no process killed
Insert dvr_common driver done.
Platform GM812600
    enc_in0=(buf: 1843200,4,0)
RTMP_TimerListAdd: add timer obj c8a49f60!
    enc_in0_d=(buf: 1843200,4,1)
    enc_out0=(res: 1280,720)
    enc_out0=(buf: 783360,4,0)
    ssenc_out0=(buf: 783360,1,0)
    enc_in1=(buf: 450650,4,0)
    enc_in1_d=(buf: 450650,4,1)
    enc_out1=(res: 640,352)
    enc_out1=(buf: 191488,4,0)
    ssenc_out1=(buf: 191488,1,0)
    enc_in3=(buf: 112640,4,0)
    enc_in3_d=(buf: 112640,4,1)
    enc_out3=(res: 320,176)
    enc_out3=(buf: 47872,4,0)
    ssenc_out3=(buf: 47872,1,0)
fcap: V0.3.13
vcap_dev:
  • :bAlbum_bug=0, bCrop_bug=1, bCU_bug=0

                LL_BusDeadlock_bug=0, bSupportSplitOSDDispRamWritePort=1

fcap:
  • : Link List mode!

fcap: fosd00: minor=49
fcap: fosd02: minor=48
fcap: fosd01: minor=47
fcap: fosd03: minor=46
vcap_dev: [1]:bAlbum_bug=0, bCrop_bug=1, bCU_bug=0
                LL_BusDeadlock_bug=0, bSupportSplitOSDDispRamWritePort=1

fcap: [1]: Link List mode!
fcap: fosd10: minor=45
fcap: fosd12: minor=44
fcap: fosd11: minor=43
fcap: fosd13: minor=42
WDT base virtual address = c8c7e000
probe hm1375 i2c OK.
Capture Clock Out = 27000000
HM1375: 720HD OK
SCL: Version, v1.17
SCL: div:4
FAVC Encoder IRQ mode(29)v4.2.1
FAVC codec Max Resolution is 1280x720, built @ Apr 10 2013 11:49:19
MCP100 driver with CPU for VG,
GM8126 MPEG4 with CPU for VG, decoder ver: 3.2.2, encoder ver: 3.2.8, built @ May 14 2012 15:30:49
GM8126 MJPEG with CPU for VG, encoder ver: 3.2.5, decoder ver: 3.1.4, built @ May 14 2012 15:30:35

FTDI210 registers 32 entities to video graph!
FTDI210 Driver v1.4 (1 engine(s))
killall: gerddns: no process killed
killall: upnp_map: no process killed
killall: upnp_map: no process killed
killall: ddns_update: no process killed
killall: mdns: no process killed
ra0       Link encap:Ethernet  HWaddr 48:02:2A:42:09:EC
motor driver init successful!
RTMP_TimerListAdd: add timer obj c8a49f88!
WDT base virtual address = c8f7c000
umount: can't forcibly umount /mnt/mtd/ipc/tmpfs/sd: Invalid argument
workthread: log init succeed.
libs_initnettype(WiFi): succeed.
warming: ini file(web.ini) not found!!!
videocomm(0): 6 1280 720
videocomm(1): 7 640 352
videocomm(2): 8 320 176
reset: 0x45003
cp -r light: 0x5414d400
/mnt/mtd/ipc/web/images/logo0.jpg /mnt/mtd/ipc/web/images/logo.jpg
cp: cannot stat '/mnt/mtd/ipc/web/images/logo0.jpg': No such file or directory
TimeZone: 4
workthread: init ini succeed.
HI_Ntp_Proc: enable=1, svr=time.windows.com, interval=6
workthread: ntpsvr init succeedencript: 0x55003
.
workthread: reset init succeed.
ptz type: motor
ptz motor: hrange=1500, vrange=500
ptz motor: hpos=540, vpos=211
ptz motor: hspeed=0, vspeed=0
ptz motor: hscan=1, vscan=1
workthread: ptz init succeed.
extalarm: 0x55555500
GPIO-0 autorequested
fcap:
  • :OSD P0 default fonts num=42


vidfcap:
  • :OSD P1 default fonts num=42


eoqv: min=14, max=45, init=23.
sensor: 22
frequency: 50
extalarm: off open
encode(chn=0): resolution=6,cbr=0,bitrate=1024000,frame=12,iframe=24,quality=0,noise=0
encode(chn=0): audioenablefcap: [1]:OSD P0 default fonts num=42

=1,fcap: [1]:OSD P1 default fonts num=42

 audiotype=2

----------SDK before open dvr_enc: 0 ----------

MD_INIT (80 x 45).
encode(chn=1): resolution=7,cbr=0,bitrate=1024000,frame=25,iframe=50,quality=0,noise=0
encode(chn=1): audioenab
H264 rate control version: fix 0.96
le=1, audiotype=2

--------Platform 8126 version 81262220
--fcap:
  • :IN=HM1375

SDK before open Rcv Wcid(1) AddBAReq
dvStart Seq = 00000000
r_RTMP_TimerListAdd: add timer obj c8a4b374!
enc: 1 ----------
encode(chn=2): resolution=8,cbr=0,bitrate=256000,frame=2Rcv Wcid(1) AddBAReq
5,Start Seq = 00000000
ifRTMP_TimerListAdd: add timer obj c8a4b3b4!
rame=50,quality=0,noise=0
encode(chn=2): audioenable=1, audiotype=2

----------SDK before open dvr_enc: 2 ----------
OSD(area=0): show=1, x=976, y=0, str=YYYY-MM-DD hh:mm:ss
OSD(area=1): show=1, x=0, y=0, str=IP Camera Garage
audiovol: 65 46

--------SDK ENC_START 0 -------
HI_Media_SDKInit: HI_SDK_StartEncode(chn=0) succeed.

--------SDK ENC_START 1 -------

##### Transfer Group 0 Done,213ms!
libs_GetNTPTime: 1440145268
HI_RTC_SetTime: succeed(2015-08-21 05:21:08).
HI_Media_SDKInit: HI_SDK_StartEncode(chn=1) succeed.

--------SDK ENC_START 2 -------

##### Transfer Group 1 Done,148ms!
Platform 8126 version 81262220
fcap: [1]:IN=HM1375

Frammap: 3358 pages in DDR0 are freed. n=2) succeed.


##### Transfer Group 2 Done,151ms!
Video Encode chn 0 Tid: 352
Video Encode chn 1 Tid: 353
Video Encode chn 2 Tid: 354
Audio Encode Tid: 349
OSD Tid: 348

HI_Record_Stop
relay: 0x55000
wifikey: 0x1c000004
HI_Media_RecInit: HI_Record_SWDT base virtual address = c93f6000
tart(chn=0) succeed.
HI_Websvr_Init: init media succeed.
HI_Websvr_Init: PBServer start.
HI_Websvr_Init: webport[8080], root[/mnt/mtd/ipc/web].
infra: auto.
workthread: infrared init succeed.
workthread: wifikey init succeed.
wdt: default timeout: 20 sec.
wdt: default timeout: 5 sec.
workthread: wdt init succeed.
netdetect: WiFi (Enable).
netdetect: netflag(WiFi).
workthread: netdetect init succeed.
workthread: search start.
===================================================
ipc_server start  : 2015-08-21 05:21:08
ipc_server version: V5.4.6.2.1-20130820
===================================================
dosfsck 3.0.12 (29 Oct 2011)
dosfsck 3.0.12, 29 Oct 2011, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "        "
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
     32768 bytes per cluster
      6332 reserved sectors
First FAT starts at byte 3241984 (sector 6332)
         2 FATs, 32 bit entries
    476160 bytes per FAT (= 930 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 4194304 (sector 8192)
    118912 data clusters (3896508416 bytes)
63 sectors/track, 128 heads
      8192 hidden sectors
   7618560 sectors total
Starting check/repair pass.
tutk: start: 2015-08-21 05:21:26
tutk: TZ: STD+4:0:0DST+3:0:0,M3.2.0/2:0:0,M11.1.0/2:0:0

tutk: TZInterval: -14400
tutk: uid=FTM89WFPJ47ZBG6WM77J, full=on, svraddr=50.19.254.134, 122.248.234.207, m2.iotcplatform.com, m5.iotcplatfo
tutk: HI_IOTC_Platform_Init: IOTCAPIs   V1.9.1.0
tutk: HI_IOTC_Platform_Init: IOTCAVAPIs V1.3.1.0
tutk: login dev success! handle[0]=244304
tutk: login dev success! handle[1]=245464
tutk: login dev success! handle[2]=246624
tutk: login dev success! handle[alarm]=247784
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
HI_Media_LiveStreamRegisterMediaLink: cntindex=0,onlinenum=0
HI_Media_LiveStreamParseStream: cntindex=0,sock=29,avchn=0,mediatype=4
SendMediaDataThread(entry): cntindex=0,avchn=0,af=2,sock=29,rbhandle=4456328
onvif: login dev success! handle=3039240
tutk: start stream succeed(ret=0x0)! handle(alarm)=247784
tutk: HI_IOTC_Platform_Init: going to IOTC_Listen...
onvif: framerate:25.000000
onvif: src: w:1280 h:720
onvif: video: w:1280 h:720 w:640 h:352
onvif: devmgmt_proc ok.
onvif: remotediscovery_proc ok.
onvif: start: 2015-08-21 05:21:27
onvif: timg: productid=C5F0S7Z0N0P0L0
onvif: serverIP: 192.168.1.123
Reclaiming unconnected clusters.
Unable to create unique name
R:/mnt/mtd/ipc/tmpfs/sd/20150821/record000/(0)
S:/mnt/mtd/ipc/tmpfs/sd/20150821/images000/(0)
ptz motor: selfdet range: hor=650
SOAP 1.2 fault: SOAP-ENV:Sender [no subcode]
"Method 'wsd:Resolve' not implemented: method name or namespace not recognized"
Detail: [no detail]
ptz motor: selfdet range: ver=215
Warning: Driver for device ra0 has been compiled with version 22
of Wireless Extension, while this program supports up to version 20.
Some things may be broken...

Warning: Driver for device ra0 has been compiled with version 22
of Wireless Extension, while this program supports up to version 20.
Some things may be broken...


« Last Edit: August 21, 2015, 10:30:19 am by kirchnet »